{"id":895,"date":"2019-07-19T04:22:34","date_gmt":"2019-07-19T04:22:34","guid":{"rendered":"https:\/\/www.ted-corp.co.jp\/?page_id=895"},"modified":"2019-11-26T04:07:37","modified_gmt":"2019-11-26T04:07:37","slug":"fume","status":"publish","type":"page","link":"https:\/\/www.ted-corp.co.jp\/en\/fume\/","title":{"rendered":"Thermal oxidizer"},"content":{"rendered":"
\r\n

We can provide the most suitable oxidizer, depend on characteristic features of dryer, because we also design and manufacture dryer by ourselves.
\r\nThe systems of thermal oxidizer correspond to changes of exhaust gas volume, solvent concentration and operating conditions of the production machines.<\/p>\r\n\r\n

Direct flame type thermal oxidizer<\/h3>\r\n
\r\n
\r\n
This system eliminates harmful substances contained in the exhaust gases come from the production machine, and resolves it into the carbon dioxide and water by heating up the exhaust gases up to 700 ~ 800\u2103.
\r\nIt can easily treat the exhaust gases with little influence by the substance in the exhaust gases, and can keep high rate of the oxidization effect in the long life operation.\r\nHowever, it is said that the running cost of direct flame oxidizer is generally high. So we propose the combined system with hot air recovery system by gas-gas heat exchanger and heat recovery system by waste heat boiler (steam type or thermal oil type).<\/div>\r\n<\/div>\r\n

\"\"<\/p>\r\n<\/div>\r\n\r\n

Catalytic type thermal oxidizer<\/h3>\r\n
\r\n
\r\n
This system oxidizes the solvent at the temperature with 300 ~ 400\u2103 using platinum based catalyst.
\r\nGenerally, it uses gas or kerosene as fuel. But depending on the solvent concentration conditions, it can be operated by self-combustion with catalysis only.
\r\nIn addition, although there is a case that the catalytic function is declined by silicon and metal vapor, it can keep its life longer by using pretreatment (Guard Bed) or Catalyst Rejuvenation.
\r\nIn this system, the waste heat is recovered as hot water and hot air, or usually re-used as the heat source of the dryer.<\/div>\r\n<\/div>\r\n

\"\"<\/p>\r\n<\/div>\r\n\r\n\r\n

\"Catalytic<\/h3>\r\n
\r\n
\"\"<\/div>\r\n
\r\n

\"The<\/p>\r\n

We had developed of economical type catalytic oxidizer using poisoning resistance catalyst and we installed the system in operation for dry laminating machine.
\r\nThis system adapts “NHP” as poisoning resistance catalyst developed by Nikki- Universal Co., Ltd. who is famous as high quality catalyst supplier. By using “NHP”, the estimated life time of the catalyst becomes 3 or 4 times longer than ordinal one, and the reaction efficiency for ethyl-acetate-containing exhaust gas is improved remarkably with the low temperature in the range of 250 ~ 300\u2103.
\r\nIn addition, we propose energy saving system recovering the surplus waste heat to use as heat source for the dryer, and system for CO2 emission treatment.<\/p>\r\n<\/div>\r\n<\/div>\r\n\r\n

\r\n

\u25b2 Page Top<\/a><\/p>\r\n <\/div>\r\n\r\n

Regenerative thermal oxidizer (RTO)<\/h3>\r\n
\r\n
\r\n
This system is suitable for low solvent concentration. Using regenerative media, it oxidizes the solvent keeping high heat recovery rate around 80-95%.
\r\nThe temperature required for this system is 800 ~ 900\u2103 , which is higher than direct flame type. But by using suitable regenerative media, the running cost can be reduced toward the level of one tenth or twentieth of the running cost of direct flame type. In addition, it can be operated by self-combustion at 500ppm of toluene base. In the case of high concentrated exhaust gas, steam recovery also is possible.<\/div>\r\n<\/div>\r\n

\"\"<\/p>\r\n<\/div>\r\n\r\n\r\n\r\n\r\n

Thermal oxidizer combined with VOC concentrator<\/h3>\r\n
\r\n
\r\n
Although the oxidization efficiency slightly down to 80-95%, this system is suitable to oxidize low solvent concentration and low temperature exhaust gas. First, exhaust gas comes through the rotary adsorption unit, called as “Rotor” made by activated carbon or hydrophobic zeolite material, and the solvent is removed or adsorbed here. Secondary, the absorbed and removed solvent is treated by hot air with about 1\/10 of exhaust gas volume.
\r\nIn this way, the exhaust gas highly concentrated about 10 times is treated with smaller oxidizer. At the same time, the recovered high temperature exhaust gas is re-used as the hot air for the solvent removal and adsorption.<\/div>\r\n\r\n<\/div>\r\n

\"\"<\/p>\r\n<\/div>\r\n\r\n\r\n

\"Exhaust<\/h2>\r\n
\r\n
\r\n
In case there are more than two printing presses, it is not economical to install the thermal oxidizer for each printing press, because of limited installation space in the printing plant. Therefore, it becomes common to set up one large size oxidizer to treat the exhaust gas from two printing presses or more.
\r\nRecently, considering the additional installation of the printing press in future, the idea to install one 500Nm3\/min scale oxidizer connected with common exhaust gas header from printing presses was adopted with the controlling the number of oxidizer system according to the operating condition of the printing press.
\r\nThis system makes it possible to minimize the running cost of oxidizer and can add the oxidizer step by step according to the number of the printing presses.<\/p>\r\n<\/div>\r\n<\/div>\r\n
\"\"
Schematic drawing for control system of the oxidizers<\/figure><\/div>\r\n<\/div>\r\n\r\n
\r\n\t
\r\n\t\t

<\/i>For product inquiries<\/a><\/p>\r\n\t<\/div>\r\n<\/div>\r\n\r\n<\/div>\r\n","protected":false},"excerpt":{"rendered":"We can provide the most suitable oxidizer, depend on characteristic features of dryer, because we also design […]

Read More…<\/a><\/p>","protected":false},"author":2,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_locale":"en_US","_original_post":"893"},"_links":{"self":[{"href":"https:\/\/www.ted-corp.co.jp\/wp-json\/wp\/v2\/pages\/895"}],"collection":[{"href":"https:\/\/www.ted-corp.co.jp\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.ted-corp.co.jp\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.ted-corp.co.jp\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.ted-corp.co.jp\/wp-json\/wp\/v2\/comments?post=895"}],"version-history":[{"count":8,"href":"https:\/\/www.ted-corp.co.jp\/wp-json\/wp\/v2\/pages\/895\/revisions"}],"predecessor-version":[{"id":1937,"href":"https:\/\/www.ted-corp.co.jp\/wp-json\/wp\/v2\/pages\/895\/revisions\/1937"}],"wp:attachment":[{"href":"https:\/\/www.ted-corp.co.jp\/wp-json\/wp\/v2\/media?parent=895"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}